ETS manufactures access control card reader converters and adapters. We are very familiar with card reader technologies and their data formats.
If you don't see what you need below, call us. In most cases, we can develop a product that will meet your needs economically. Currently, we
manufacture: The PR1 Parallel reader adapter, the RDAO-1 optically isolated and RDA-1 reader distribution amp, and the WC1 Wiegand converter.

 

   Go to ETS Main Page

   Go to Systems Integrator Specialty

      
  Products Main Page


 

 

ETS
Electronic Technical Services Inc.
211 Conchas SE
Albuquerque, NM 87123

Phone: 505-888-3923
Fax: 505-888-3926

Toll Free: 866-700-3923

E-mail:  sales1@etsnm.com

 

 

 

Made in U.S.A.    

 

Access Control Reader Converters and Adapters
 

PR1  Parallel Reader Adapter

Allows two access control card
readers (Wiegand or Magstripe) to
be connected to a single reader
input. Useful for saving reader
ports on access control panels and
/ or doors that require card readers
on both sides.

  • 2 LED drivers for each
    reader.
  • Buffered reader data output.
  • Jumper configurable for any
    reader type.
  • Easy cable run terminations.
  • Power: 12VDC @ 10mA.
  • 5v regulator for reader power
  • Reverse polarity protected
  • Dimensions: W 3.40 x L 4.80

E-mail sales1@etsnm.com
or Call 866-700-3923 for Pricing



   
Product Specification Sheet

 Installation Instructions



RDAO-1  Opticall Isolated Wiegand
Card Reader Distribution Ampifier

The RDAO-1 is 3 port, Wiegand reader
distribution amplifier with optically isolated
inputs and outputs for access control
systems.
 All three ports are optically
isolated from one another which prevents
ground loop caused data corruption issues.
The RDAO-1 Monitors the LED outputs of
the access control panels and outputs an
LED indication of “access granted or denied”



E-mail sales1@etsnm.com
or Call 866-700-3923 for Pricing




Product Specification sheet

Installation Instructions


RDA-1  Wiegand Card Reader
Distribution Ampifier

Distributes the data from one
Wiegand reader to up to three data
access control panels. Monitors
the LED outputs of the data panels
and outputs an LED “access
granted“ in the case of any panel
valid card read or a “access
denied” if all three data panels
report non-valid card reads.
 

  • Buffered reader data outputs.
  • 2 LED input and output channels.
  • Easy cable run termination.
  • Power: 12VDC @ 10mA.
  • 5v regulator for reader power
  • Reverse polarity protected
  • Dimensions: W 3.00 x 4.10

E-mail sales1@etsnm.com
or Call 866-700-3923 for Pricing




   
Product Specification sheet


Installation Instructions


WC1  Cardkey L9 Wiegand
Converter

Converts Cardkey(tm) L9 single
wire reader signals to standard 2
wire Wiegand signals. The WC1
also has 2 incandescent lamp
drivers for controlling the L9
reader lamps.

  • Buffered reader data output.
  • Filament warming circuit extends L9 reader lamp life.
  • Easy cable run terminations.
  • Power: 12VDC @ 10mA.
  • 5v regulator for reader power
  • Reverse polarity protected
  • Dimensions: W 1.60 x L 3.00

 


E-mail sales1@etsnm.com
or Call 866-700-3923 for Pricing



   
Product Specification sheet
 

Installation Instructions

Copyright ETS Inc. 2020